Get my home cleaned
A clean grey tiled bathroom with a frameless glass shower screen and a timber vanity

How-to guide

Grout sealing

Seal the grout in your shower, bathroom or kitchen yourself, step by step. What matters most is the start: seal only grout that is clean and completely dry.

Updated 13 November 2026. Health and safety points come from three government sources, listed at the end.

The short answer

Grout sealing soaks a clear penetrating sealer into cement grout to help it resist spills and dirt. Repair any cracks, scrub the grout clean and let it dry completely, which can take up to 24 hours. Seal the lines a small section at a time, wiping sealer off the tiles before it dries. Add a second coat, check that drops of water bead, then keep it dry for at least 24 hours.

What you need

  • Clear penetrating grout sealer
  • Grout cleaner or mild detergent
  • Stiff grout brush
  • Clean dry cloths
  • Brush-on or spray applicator
  • Protective gear from the label
Step by step

How to seal grout, step by step

For cement grout on walls, floors and in showers.

  1. Check the grout type and any old sealerCement grout is porous, so unsealed grout takes in water and stains sooner. Epoxy grout does not need sealing. Put a few drops of water on old grout and wipe them off after 5 minutes: if they soaked in or left it darker, it is not sealed. Repair cracked or missing grout and strip any peeling sealer first.
  2. Scrub the grout cleanScrub the lines with a tile and grout cleaner, or water and a mild detergent, and a stiff brush. Treat any mould with a product made for it, following the label. Wipe off the residue with a damp cloth, as sealer locks in any dirt left behind.
  3. Let the grout dry completelyAllow up to 24 hours, or 24 to 48 hours in humid weather or a shaded spot, with the shower out of use. If in doubt, wait longer, as damp grout can stay dark after sealing. Let new grout fully cure first (see where the guides disagree, below).
  4. Test a patch and air the roomTry the sealer on a small hidden area first. Seal only at 10 degrees C or warmer. Keep the room well ventilated, put on the gear the label lists, and protect nearby surfaces if you are spraying.
  5. Seal a small section, wiping as you goRun a brush-on sealer along each joint, or spray evenly along the lines, for an even coat with no puddles, as too much may discolour some grout. Wipe any sealer off the tiles with a clean, dry cloth before it dries, or it can leave marks or a haze.
  6. Add a second coat, then test itMost sealers need more than one coat, so apply the next after the drying time on the label. Then put a few drops of water on the dry grout. If they bead on the surface, the seal is sufficient. If they soak in, add another coat.
  7. Keep it dry for at least 24 hoursKeep water, spills and dirt off the sealed grout for at least 24 hours, so leave the shower unused. Light foot traffic is usually fine after about 2 hours. Curing times vary by product, so check the label.
What you need

What you need to seal grout

Get these together before you start.

Clear penetrating grout sealer

A penetrating sealer soaks into the grout rather than sitting on top as a film. Check the label suits your grout and tiles, and buy enough for more than one coat.

Grout cleaner or mild detergent

A tile and grout cleaner, or water with a mild detergent, to lift the dirt first. For mouldy grout, add a product made for mould.

Stiff grout brush

A stiff-bristled brush to scrub dirt, stains and mildew out of the grout lines. A small brush or an old toothbrush works too.

Clean dry cloths

Plenty of clean, dry cotton or microfibre cloths, or paper towels, to wipe stray sealer off the tiles before it dries.

Brush-on or spray applicator

Brush-on sealer is more precise and suits small spaces. Spray suits large areas, but takes more preparation to keep overspray off nearby surfaces.

Protective gear from the label

The protective clothing, eye protection and dust mask or respirator that the label or safety data sheet lists for the product.

Health and safety

Staying safe when you seal grout

From Australian government pages, none of them about grout sealer by name.

SafeWork SA

Work in a well-ventilated room

SafeWork SA's page on adhesives and sealants, written for workplaces, says to use them in well-ventilated areas and avoid inhaling the vapours, as certain adhesives give off toxic vapours. Where good ventilation is not practicable, it says suitable breathing apparatus, such as respirators, should be worn.

SafeWork SA

Follow the label and safety data sheet

On the same page, SafeWork SA says to follow the instructions on both the Safety Data Sheet and the label, and to check the Safety Data Sheet for protective equipment. It says skin contact should be minimised, and goggles or face shields worn with runny adhesives to protect the eyes from splashes.

Better Health Channel

If you clean mould off first

On removing mould at home, the Better Health Channel says to make sure there is good ventilation and wear protective clothing, such as a shower cap, rubber gloves, eye protection, overalls, suitable footwear and a P1 or P2 face mask.

NSW Government

Before you repair old grout

The NSW Government's asbestos website says asbestos can be found in adhesives like grout, sealants, putties and dry powder mixes made before 1987. It advises having a licensed asbestos assessor check the property.

By grout and tile

Sealing different grout and tiles

What changes with the grout and the tiles around it.

Grout or tileWhat to do
Cement groutIf you seal, use a penetrating sealer. Cement grout is porous, so in a shower water gets into it with every use.
Epoxy groutIt needs no sealer, as it does not soak up water, soap and stains the way cement grout does.
Glazed ceramic or porcelain tilesThe tiles rarely need sealing. If you seal the grout, wipe any sealer off the tile faces.
Natural stoneStone tiles usually need sealing, with products that suit stone. Test a patch first, and keep vinegar and other acids off marble, travertine and limestone.

Checked on 12 November 2026.

Where guides differ

Where the guides disagree

Guides split on these points. Here is each side, with its caution.

How long to leave new grout

One sealer maker says new grout needs 24 hours to dry before sealing, and others say at least 72 hours. Another sealer maker says 28 days, warning that sealing earlier traps moisture inside the joint and weakens both the joint and the sealer's grip.

Vinegar before sealing

One sealing guide lifts stains with a 50/50 mix of vinegar and water. Another warns that acid cleaners can damage cement grout if left on too long. Acids, including vinegar, can also etch marble, travertine and limestone.

Do you need to seal at all?

Sealing guides favour it, as unsealed cement grout takes in water and stains. One cleaning business does not recommend it as standard: it says a sealer needs stripping before it can be redone, and adds a cost most homes do not need. Sealing the grout is your call.

Afterwards

Keeping sealed grout in good shape

How to make the sealer last, and when to seal again.

Clean it gently

Bleach, acid and solvent cleaners wear sealers down faster, so clean sealed grout with a pH-neutral cleaner.

Reseal when water soaks in

A clear sealer usually lasts 1 to 5 years, depending on the product, foot traffic and the cleaners you use. Repeat the water test now and then, and reseal when the drops soak in.

Official sources

Checked on 13 November 2026.

  1. SafeWork SA, Adhesives and sealants
  2. Better Health Channel, Mould removal at home
  3. NSW Government asbestos website, Adhesives, dry powder mixes and asbestos

Get a tile and grout cleaning quote